M8, Female panel mount connector, IP67/IP69K, Contacts: 4 | 86 6218 0002 00004

Menu

Menu

Products
Automation technology - Sensors and actuators
M8
M8 Female panel mount connector, Contacts: 4, solder, IP67/IP69K, M10x0.75, Front mounting, with solder cups

Illustration M8 Female panel mount connector, Contacts: 4, solder, IP67/IP69K, M10x0.75, Front mounting, with solder cups — Illustration

Scale drawing M8 Female panel mount connector, Contacts: 4, solder, IP67/IP69K, M10x0.75, Front mounting, with solder cups — Scale drawing

Assembly instructions M8 Female panel mount connector, Contacts: 4, solder, IP67/IP69K, M10x0.75, Front mounting, with solder cups — Assembly instructions

Assembly instructions / Panel cut-out M8 Female panel mount connector, Contacts: 4, solder, IP67/IP69K, M10x0.75, Front mounting, with solder cups — Assembly instructions / Panel cut-out

Contact arrangement (Plug-in side) M8 Female panel mount connector, Contacts: 4, solder, IP67/IP69K, M10x0.75, Front mounting, with solder cups — Contact arrangement (Plug-in side)

Mounting orientation M8 Female panel mount connector, Contacts: 4, solder, IP67/IP69K, M10x0.75, Front mounting, with solder cups — Mounting orientation

Part no.	86 6218 0002 00004
Connector design	Female panel mount connector
Version	Panel mount Connectors
Connector locking system	screw
Termination	solder
Degree of protection	IP67/IP69K
Connection cross-section	0.14-0.34 mm² / AWG 22
Temperature range from/to	-40 °C / 85 °C
Weight (g)	5.29
Customs tariff number	85369010
Country of Origin	DE

Rated voltage	50 V (AC) / 60 V (DC)
Rated impulse voltage	1500 V
Rated current	2 A (0.14 mm²)/4 A
Insulation resistance	> 10⁸ Ω
Pollution degree	3
Overvoltage category	III
Insulating material group	II

Housing material	CuZn (Brass nickel plated)
Contact material	CuSn (bronze)
Contact plating	Au (gold)
REACH SVHC	None (No pollutants)
SCIP number	SCIP-number not available

Low Voltage Directive	2014/35/EU (EN 60529:1991 \| 2014/35/EU;EN 60204-1:2018)

Report error on this page

Security notices

The connector must not be plugged or unplugged under load. Non-observance and improper use can result in personal injury.
The connectors have been developed for applications in plant engineering, control and electrical equipment construction. The user is responsible for checking whether the connectors can also be used in other areas of application.
Connectors which are used in circuits with voltages dangerous to the touch may only be installed and used by, or under the supervision of, persons with electrical engineering training, taking into account the applicable regulations and standards.
The user must take suitable safety precautions to ensure that the connector cannot be accidentally disconnected.
Plug connectors with enclosure protection IP67 and IP68 are not suitable for use under water. When used outdoors, the plug connectors must be protected separately against corrosion. For further information on the IP protection classes, please refer to the "Technical Information" download centre.
Please observe the pollution degree and the overvoltage category. For further information, please refer to the download center "Technical Information".
To lock the cable connector with the device connector, the threaded ring is tightened "hand-tight" (approx. 40 cNm). A torque wrench for SW9 is available as an accessory (order no. 07 0085 000).

Downloads

Data sheet 86 6218 0002 00004

86 6218 0002 00004

86 6218 0002 00004

86 6218 0002 00004

Declaration of conformity

Low Voltage Directive

UKCA declaration of conformity

Electrical Equipment

STP-Data 86 6218 0002 00004